2021-12-25

A-10 Thunderbolt II (aka Warthog) Wood Toy Airplane Build

 

A-10 Thunderbolt II (aka Warthog) Wood Toy Airplane Build

My Granson has repeatedly asked for one of these for several weeks every time I see him. I made this one for him for Christmas. Originally I had not intended to make one of these because I don't like the size, and it the details are not correct, but my grandson is seven and probably will not notice.
 
Drilling The Engine Nacelle For An A-10 Thunderbolt Wood Toy Airplane
Drilling The Engine Nacelle For An A-10 Thunderbolt Wood Toy Airplane

 
 

The first problem I had was drilling the center hole. The plans say to drill the hole 1-inch deep. It does not need to be that deep. I drilled half that far, and 1/4-inch would have been enough. I had trouble getting the hole centered using my drill press and a heavy vise. When the point of the bit first made contact with the end of the dowel, the end grain would cause the bit to shift slightly. Next time I will need to break out the lathe chuck

The second problem I had was drilling the holes for the dowels in the Nacelle. I tried everything I could think of to drill the hole straight through the center and get both of them aligned well enough. Nothing worked, and after tossing several nacelles into the designer kindling bucket. I gave up and planed a flat on one side and glued them directly to the fuselage. At this point, I decided that the designer never built this himself. I don't see how you can drill holes through two nacelles and the fuselage and get all of them in perfect alignment using basic shop tools.

My second issue with the plans is clutter. There is a lot of repetition in the plans. How many times do I need to see the list? Parts that need to be cut with a scroll saw are mixed with parts and other things that do not need to be. In this case, all of the parts that need to be printed will fit on one page. I did this using Inkscape. I have the computer skills to do this work, but many people do not. 

 

A-10 Thunderbolt II (aka Warthog) Wood Toy Airplane Glued and Clamped
A-10 Thunderbolt II (aka Warthog) Wood Toy Airplane Glued and Clamped

Glue up was straightforward. I apply glue and wait a few minutes (5 or less this will vary with the glue used) to let the glue get tacky so it does not slip so easily when the clamps are added. In the picture, there are two sets of clamps and four parts. I glued the pieces on the bottom of the wings first, turned the plane over, and added the nacelles using the same procedure. At this point, I set the timer on my phone for 15 minutes and do something else. I use Titebond II, and the times come from the manufacturer.


A-10 Thunderbolt II (aka Warthog) Wood Toy Airplane With all the parts glued together except the wheels.

Another issue I have with the plans is the pattern for the fuselage. The fuselage is a compound cut, but instead of a conventional compound cut pattern where both sides are one pattern that you fold around the corner of the wood, and easy to get the two sides aligned perfectly. I fixed this in Inkscape. 

A-10 Thunderbolt II (aka Warthog) Wood Toy Airplane Completed Top View
A-10 Thunderbolt II (aka Warthog) Wood Toy Airplane Completed Top View

Tools I used:


  • Hitachi 12-inch miter saw/
  • Shopsmith Bandsaw
  • Shopsmith Drill Bits
  • Shopsmith Belt Sander
  • Central Machinery Drill Press
  • Palmgren Vise
  • Dozuki 22 TPI saw
  • Freud Wave Cut Forstner Bits
  • Assorted Squares
  • Rulers
  • Excalibur Scroll Saw
  • Pegas #3 MGT Blades
  • Bauer Random Orbit Sander (Harbor Freight)
  • Delta 1x36-inch Belt Sander
  • Pittsburgh Clamps
  • Jorgensen Clamps 
  • Unbranded Large Nylon Spring Clamps

 

Woods Used

  • Poplar
  • Walnut
  • Ipe
  • Birch
 

I don't have this in my shop as of the post. I may add one at a later date.

#odinstoyfactory #handmade #woodtoys #airplane #aircraft, #toy #warthog #thunderbolt

 





Dragon Clock Christmas Gift My First Clock

Dragon Clock Christmas Gift My First Clock


I made two of these for Christmas gifts. It was the first time I ever made a clock.

I had initially intended to cut this from solid wood, but the only piece I had was not flat enough to cut on a scroll saw. Flattening the board would take at least 1/4-inch off the wood, and I didn't want it to be that thin, so I decided to cut it from 19mm Baltic Birch plywood. Plywood is a much better choice than solid because it will not break easily.

I bored the hole for the clock using a 2-3/8 Forstner bit as per the pattern instructions. I had never drilled a hole this size before. I had to drill with very light pressure to keep the drill press from stalling. At first, I thought the bit was slipping in the chuck; this was not the case. The drill press belt was slipping. I put as much tension o the belt as I could, and it would still slip. More tension helped, but it didn't stop them from slipping. My drill press has a link belt. Perhaps I should remove a link or two from the belts.

The next time I make one of these, I will try cutting the hole with my scroll saw. It does not have to be perfect, just close enough to hold the clock movement in place.

I don't have a Dragon Clock in my shop yet, but I plan to have one soon.
Check out the many other dragons I have there.

My Shop
http://odinstoyfactort.etsy.com

2021-12-20

Handmade Miniature Birdhouse Christmas Tree Ornament 1113816884

 

Handmade Miniature Birdhouse Christmas Tree Ornament
Handmade Miniature Birdhouse Christmas Tree Ornament

Buy Now
https://www.etsy.com/shop/odinstoyfactory?section_id=27235904

A handmade miniature birdhouse Christmas tree ornament I made from hardwood. Decorate your tree, or it makes a unique gift or stocking stuffer.

Approximate Size:
Height: 3.75 Inches
Width: 1.25 Inches
Depth: 1.25 Inches

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament



#odinstoyfactory #handmade #birdhouse #madeinusa #madeinamerica #christmas #gift #ornament #stockingstuffer #1113628114



2021-12-19

Handmade Miniature Birdhouse Christmas Tree Ornament 1113628114

 

Handmade Miniature Birdhouse Christmas Tree Ornament
Handmade Miniature Birdhouse Christmas Tree Ornament 
 

Buy Now
https://www.etsy.com/shop/odinstoyfactory?section_id=27235904


A handmade miniature birdhouse Christmas tree ornament I made from hardwood. Decorate your tree, or it makes a unique gift or stocking stuffer.


Approximate Size:
Height: 3.5 Inches
Width: 1.25 Inches
Depth: 1.25 Inches

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament

Handmade Miniature Birdhouse Christmas Tree Ornament


#odinstoyfactory #handmade #birdhouse #madeinusa #madeinamerica #christmas #gift #ornament #stockingstuffer #1113628114

2021-12-17

Handmade Miniature Birdhouse Christmas Tree Ornament 1113556918

 

Handmade Miniature Birdhouse Ornament
Handmade Miniature Birdhouse Ornament


Buy Now
https://www.etsy.com/shop/odinstoyfactory?section_id=27235904

A handmade miniature birdhouse Christmas tree ornament I made from hardwood. Decorate your tree, or it makes a unique gift or stocking stuffer.

Approximate Size:
Height: 3.75 Inches
Width: 1.25 Inches
Depth: 1.25 Inches


Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

Handmade Miniature Birdhouse Ornament

#odinstoyfactory #handmade #birdhouse #madeinusa #madeinamerica #christmas #gift #ornament #stockingstuffer #1113556918