Bad Bob's Custom Motors - Handmade Wooden Toy Car Bodies Completed

Bad Bob's Custom Motors - Handmade Wooden Car Bodies - Coupe & Sedan
Bad Bob's Custom Motors - Handmade Wooden Car Bodies - Coupe & Sedan
Most of the sanding was done with belt sanders. Delta Model 31-340 1x48-inch Belt Sander and my Shopsmith 6x48-inch belt sander. I consider belt sanders essential to a toy makers shop.


Before sanding, I rounded over the corners with a clean, sharp 1/8-inch radius round over bit paying very close attention to grain direction to prevent as much tear out as I can. It's ok to back route when doing this because the cut is so small. You can do the round over by hand with sandpaper but the router is more consistent and faster.


The rest of the sanding was done by hand using various sanding tools I have made and fingernail file scraps.

Delta Model 31-340 1x48 inch belt & 8 Inch Disk Sander
Delta Model 31-340 1x48 inch belt & 8 Inch Disk Sander




Shopsmith - 6x48" Belt Sander
Shopsmith - 6x48" Belt Sander

Comments

Post a Comment

Popular posts from this blog

Handmade Wooden Dinosaur Pterodactyl Figurine Handmade and Finished From My Buddies Dinos Collection - 655979018

Image
Buy This Dinosaur Today My Buddies Dinosaur Collection All My Dinosaurs Welcome to my shop, where I handcrafted this unique Pterodactyl dinosaur figurine from carefully selected hardwoods using traditional woodworking tools. Approximate Dimensions: Length: 6-5/8 inches Height: 4 inches I use a custom blend of mineral oil, beeswax, and carnauba wax to give each figurine a smooth, durable, renewable, and natural finish that enhances the beauty of the wood. Because working with natural wood is unique, every dinosaur I create is one-of-a-kind. The item you receive may vary slightly from the one pictured in the photos, but that's the beauty of it. The natural variations in wood grain, color, and knots add to the character and charm of each piece, making it truly special. I take great pride in creating these handmade treasures in Tallahassee, Florida, USA. Don't hesitate to contact me if you have a specific wood preference or want a custom order. I'll do my best to accommodate yo
Read more

What kind of paint are you using for your Bad Bob's Custom Motors cars?

Image
Bad Bob's Custom Motors I use a variety of paints from various sources. I like the acrylic house paints the best. All of the paints are nontoxic when cured.  I like to use a white primer to seal the wood and make the colors pop. In this case, I am using Zinsser B-I-N shellac based primer.  I prefer to use an airbrush for painting toys but, I have to paint outdoors, and the weather where I live does not cooperate, and I have to wait or use a brush. I used an airbrush for these wooden toy cars. My airbrush is a Badger Anthem 155.  I prefer acrylics over all other paints. They clean up easily, cover well, and are readily available in a vast array of colors. To clean, I flood with water to get rid of the bulk of the paint. The remaining paint is easily removed with ammonia-based cleaners such as window cleaner. I use household$ ammonia to remove dried paint.  I used the following to paint these wooden toy car bodies. Pink - Behr Acrylic House Paint Green - Apple Barrel Gl
Read more

Testing Anita's Acrylic Craft Paint

Image
2017-05-08 18.20.48 - Wooden Toy - Play Pal - Trailer - Truck - Orange - Anita's - Acrylic - Craft - Paint I painted these two trailers with Anita's All Purpose Acrylic Craft Paint. I didn't use a primer or sealer coat of any kind. The paint was applied with a brush just as it came from the bottle. This is the first coat of paint. I was quite surprised at how well it covered the wood. The orange paints I have used in the past did not cover well at all.   Usually requiring multiple coats to get to the point where I could not see through it.  It raises the grain a lot but I expected this. Water based finishes of any kind will raise the grain. Etsy Store: http://OdinsToyFactory.com #WoodenToys #WoodToys #WoodenToyTruck #WoodToyTruck #OdinsToyFactory #Handmade
Read more